In this blog post we will be discussing how to put lights on a dirt bike without a battery. There are many tools that you may need for the installation, and there are also several steps involved in installing these lights on your dirt bike. You’ll first want to make sure that the wiring is intact and functional before beginning to install any new parts. This blog post will go over what you need and how to install them properly so that they work when it’s time for night riding!

The first thing that you need to do for your dirt bike is to make sure that your lights work. This will be important at night and in foggy weather. The best kind of light is one that can work well in the rain too. Allow us to explain how to put lights on a dirt bike without a battery.

How To Put Lights On a Dirt Bike Without a Battery

Here is your step by step guide on how to put lights on a dirt bike without battery!

1. Find a good place to put your LED light. You need to make sure that it will be able to light up the ground well on all sides and that it is in a good position. Put the top fastener through the hole in the bottom of the lamp where you want it, as long as there is enough space inside for your LED light.
2. Next, put the switch on the handlebars, and then mount the rectifier where it is most comfortable. Make sure that it is well fixed and not loose. Put in the gas tank with a tight connection to the rectifier.
3. There are two wires coming from the magneto that go to the rectifier. We need to attach them and connect them with a wire of each color: red and black. The negative side will go to the light, while the positive will go to the switch first then back out again.
4. The wires need to be connected to the light. You’ll have to use a connector. One wire is black, one is blue, and one is brown.
5. Put the wrench on the bike so you can fasten it. If you’re not using a stand, lower your bike from the raised platform.
6. Check to make sure your bike lights are on. Turn on the handlebars and see if the light is working. When you are at home, do this by yourself and you’ll see that it’s not hard.

Remove The Seat And The Gas Tank

To do the wiring, you need to remove both the seat and gas tank from your motorcycle. By doing this, you will be able to get to the place where the wires will go through. You should have all of the tools needed for this job already. Turn some bolts with either a spanner or wrench depending on what size is needed. If the bolts are larger, then you will need a larger spanner. And if they are smaller, then you will need a smaller one. This is logical. When you have taken off the bolts that hold both the seat and the gas tank, put them in a safe place.

Tools Needed For Installing Lights on a Dirt Bike

What you need for this is the right tools. You have to take care of your dirt bike before you mount the lights. First, make sure it’s on a raised surface with all the engines turned off. Then, hang or raise it up high and be careful not to have an accident.

Insulated Wires

You will need to wire your house. The wires have different colors on them. You should get black and red ones, or other colors so that you can tell which wire goes where. If you want to make changes in the future, you will be able to notice the wires so that you know what they are for.

LED Spotlight

None of the tools are necessary if you don’t have an LED spotlight. This is the light that you’ll be mounting on your dirt bike. It should be mounted not so high but also not too low. It should be mounted somewhere in between, high enough to provide good lighting.

Bolts

The lights and the rectifier get held up with bolts. You will need to fasten them together so they don’t fall all the way down.

Pliers

A pair of pliers is a tool that will help you remove insulation or other materials on wires. With a pair of pliers, you can squeeze the cover and then pull it back to expose the wire. You should not use your teeth for this!

Spanner

The spanner will be helpful when you need to remove the seat or gas tank and take apart some nuts. You should find a size that is correct for your dirt bike, so you will need to look into it yourself.

Driller

When you are putting up lights, you might have to make holes in the wall so that the wires can pass through. If this is true, a driller is a good tool to use. Drillers can make professional looking holes like these.

Rectifier

A rectifier is a machine that changes the power from AC to DC.

Bullet Connectors

These will be good for making the connections in the wiring.

About light
“mini bike light bar”
“mini bike led light kit”
“mini bike light generator”
“mini bike tail light kit”
“coleman mini bike light kit”
“mini bike led headlight”